Jump to content

Leaderboard

Popular Content

Showing content with the highest reputation on 12/09/19 in all areas

  1. To night fitted the aerial to the wing ,had to go into the engine bay ,thatโ€™s as far as l got as itโ€™s raining All painting has now been done Back on its wheels, Started fist time runs sweet Sticky on the drive getting all wet Going to put it on some more sites tonight,Possibly on eBay on Saturday (hate putting cars on eBay)
    2 points
  2. Great post. Pictures like this are worth there weight in gold. Good luck with the project.
    1 point
  3. Thanks Jess all downloaded.forgot to mention once engine has warmed up a bit she purrs so just a cold start prob.will check over the system over the weekend.
    1 point
  4. Temp sensor for jetronic. Edit - found it. http://www.type17.ch/downloads/Injection/Bosch - L-Jet - Troubleshooting.pdfhttp://www.cardiagnostics.be/-now/Educational_sites_bestanden/BOSCH L-Jetronic Injection Manual.pdf And new item https://www.ebay.ie/itm/Temperature-Sensor-20E-25E-30E-Kadett-Manta-Monza-Senator-Commodore-Cih-GTE-/123816556178
    1 point
  5. Looks like my memory of fifty odd years ago isn't so good!!!! it must have been 33 inch pounds then not foot pounds on the Transit vans. Have a good day mate.
    1 point
  6. Not much done with the black coupe, as itโ€™s going to be a wait for dipping. managed to strip one axle, and started to clean up the 4ha to have spring hangers welded on. However, currently travelling back on ferry with the following that will be an interim side project with some bits from the black coupe. And the Redtop I have. not sure if I will take it too far away from standard though, in all cases I will keep the std bits so it can be reverted back ๐Ÿ‘
    1 point
  7. Productive day today, front bumper fitted, front indicators stripped cleaned and fitted, bulk head rubbers fitted, brake servo fitted, bits of wiring routed and fitted around engine bay, new pipes from tank to fuel filter and pump fitted, zink plated wiper mech built up and fitted, door seals fitted and plastic tread strips fitted, Ariel fitted, oil pressure switch fitted and wired in, injection relay mounted to inner wing on zink plated mount, new dizzy cap and rotor arm fitted, recon radiator fitted, fan fitted, new fan belt fitted, rear anti roll bar fitted with zink plated brackets, lower part of dash fitted, steering wheel cowling fitted, plus lots of time spent hunting parts inbetween ๐Ÿ˜€
    1 point
  8. Not much has been done with this over the past months due to being so busy. However I managed to get a few bits done today. Handbrake that I had zink plated fitted and new cable attached, rear lights deep cleaned inside and out and all contacts 're surfaced including bulb holders, rear lights fitted to car, rear bumper fitted and original exclusive loom ran into number plate lights, spoiler side pieces fitted, rears shelf cover wet vac and fitted, rear speakers fitted, carpets previously deep cleaned and left to dry and now fitted, rear infill panel prepped, painted and fitted, going to have another good day on it tomorrow so I'll update again ๐Ÿ˜Š on another note I've managed to track down a real nice clean pair of door cards, a new old stock genuine rear box with stainless tail pipe, genuine GM rubber floor mats. I've also managed to track down the original service booklet, and all thanks to a few of our fellow members, thanks gents ๐Ÿ‘๐Ÿ‘
    1 point
  9. rx8 engine to go with the box would be great super light engine about the size of a shoe box 9000 rpm nice
    1 point
  10. Ok as promised the RX8 6speed. Got family stuff to do this weekend, so not mated it up to the red top yet, will do that Tuesday maybe. Pictures attached. If anyone canโ€™t see pictures pm me and I will host on Flickr etc. More of the same
    1 point
ร—
ร—
  • Create New...