Jump to content

Manta hatch

Users
  • Content Count

    121
  • Joined

  • Last visited

  • Days Won

    2

Everything posted by Manta hatch

  1. You will always get code 19 if tested without running codes 93 94 the hall sensor in the dizzy but this will not make the car run as you described it will just make the engine seem flat all the time
  2. Had this with a manta 1.8 box onto an xe and it would only work with a 4speed thrust bearing turned out to be the pressure plate on my car ps I will be removing a 1.8 engine soon from a recent purchase to fit a c20let you more than welcome to the flywheel and clutch etc if it helps save another manta
  3. Should have some of these at the unit will check later do you need a full set ?
  4. I will give you a half shaft if I get discount on a 5 stud set
  5. blue are coil pack xe cream are early xe and yellow a c20let. Cream run 2.5bar regulator blue and yellow 3bar i have cream our blue ones 30 a set plus postage
  6. Yes the lips are different I have all types the exclusive ones are quite a bit thicker il get a pic tomorrow of 2 very slightly different 400 ones and an exclusive one for all to see differences
  7. Yes the 400 spoiler is thinner on the sides that bolt to rear quarter I have both at the unit I can get pics if it helps
  8. Roof is a tedious job I cut the sunroof out then I cut about 3mm up from the roof side lips and removed all spot welds in front and rear window frames and slowly ground the lips away down the sides till I was back at the internal skin but I did have my father cast his eye other the job and he’s done a few first one he did was for Charlie from leek many moons ago I believe it just takes time cracking job so far 👍
  9. I can supply you these brackets removed from my 400r build also may have a spare number plate bracket do you need the white square inserts that push into front lower panel the screws go into which hold the number plate bracket
  10. I have one if Danny’s is no good same money
  11. Get them balanced up and set tps voltage she will purrrrr 🙂
  12. Gets right on your nerves when the fish eyes appear I am no body man that’s my fathers thing he’s been at it 30years am sure he adds something to the paint to stop this happening I will ask him later and let you no it’s a similar thing to the plasticiser stuff Another trick he learnt me is to never wipe prepped car with thinners 2k our celly always use panel wipe
  13. If this was to come for sale as is our when finished I would like first dibs if it is a genuine i240 🙂
  14. There are a lot of copy Bosch pumps around I payed nearly 100 for a genuine Bosch one from rally and competion last summer and it is very quiet compared to a surposed Bosch one I had of eBay for 45 quid that makes soon noise when asked to provide 3.5bar pressure hence y I changed it sounded like a strangled cat but still worked I didn’t want to chance my nice new forged pistons getting melted at 8000rpm when It gave up 🙂 Best pumps are the original ones of manta Astra gtes nova gtes and cav gsi etc
  15. lt77 discovery 200tdi box and r380 box discovery 300tdi don’t forget the lt77 reverse is by first on an r380 it’s were 6th gear would be stick definitely fits as I have fitted 300 stick selector to my 200tdi lt77 one my centralised spring clip broke which sets the neutral position but that’s on a discovery I no the box’s were used in triumphs etc as well in 2wd form
  16. Yes vacuum connect to end of inlet on no4 And I have manifold to put them on angle once I have done it will confirm if they contact servo our not
  17. Same angle as carbs level on carb manifold I have got an in-line with ports manifold to go on will get some pics of wanted
  18. Dcoe style jenveys .carbs also fit but no3 and 4 trumpets very close to servo and reservoir thanks for link and column advice il be of to get a mk1 pedal box this week
  19. They do fit it all depends which inlet you have some have lugs sticking The early Astra gte 16v 20xe engines has no lugs on back i have Jenveys in my cav C20xe and they just clear standard servo but no chance of fitting back plate for sausage type air filters I will be swaping mine then I find the brake and clutch pedal won’t go over the steering column have you had to adjust the column cage ? I am currently at the stage of fitting on my rally car build I literally cut the front of the servo mounting area on Wednesday night but I am at the stage we’re I mite take the whole box out and fab new box which model mk1 escort ?I will be of the rally and competion this week and see if they will do me a deal on my Mk2 1 for a mk1 set up as looks to fit a lot better
  20. Is that a mk1 escort pedal box I have brought Mk2 for mine and needs a far amount of fettling to get it to fit nice
  21. Is the gaiter your after our complete stick with mount bracket
  22. Very nice example one thing is for sure the cabs are always solid compared to mantas as they were made out of different steel
×
×
  • Create New...