Jump to content

Sticky Manta


1200bandit
 Share

Recommended Posts

Tonight masked up the engine bay one and haft hours ,forgot to that a photo as the masking up looks really good 

Painted the bonnet and front bumper 

its the best paint job l have done,

Was getting a lot of orang peal ,then all of a sudden the paint gun started to work spot on 

Not going into the garage for the next 2 days 

But so far looking excellent 

Project images are available to Club Members Only, Click to become an OMOC Member.

Project images are available to Club Members Only, Click to become an OMOC Member.

Project images are available to Club Members Only, Click to become an OMOC Member.

Project images are available to Club Members Only, Click to become an OMOC Member.

Project images are available to Club Members Only, Click to become an OMOC Member.

As for the coolant hose that goes to the throttle body it goes to the thermostat housing ,which is blanked off 

Project images are available to Club Members Only, Click to become an OMOC Member.

  • Like 1
Link to comment
Share on other sites

Had a quick check tonight miss a bit on the front bumper, mix a small bit of paint and that’s sorted 

Paint still a bit soft in the mixing pot so going to level it alone 

Have keep one sticker on the front bumper (just as a bit of the past history)

Done a photo of the masking up under the bonnet which l think is very neat 

The bonnet is looking good as well

Project images are available to Club Members Only, Click to become an OMOC Member.

Project images are available to Club Members Only, Click to become an OMOC Member.

Project images are available to Club Members Only, Click to become an OMOC Member.

Project images are available to Club Members Only, Click to become an OMOC Member.

Edited by 1200bandit
  • Like 4
Link to comment
Share on other sites

Tonight refitted the spot lights to the bumper and rework the wiring 

Painted the underside of the bonnet 

Will wax oil the front chassis legs before l refit the bumper 

The wife has some time off looking after her mum so may not get a lot done over the next week or so

Will remove the masking as don’t need the masking tape hard to come off and damage the paint

Project images are available to Club Members Only, Click to become an OMOC Member.

Project images are available to Club Members Only, Click to become an OMOC Member.

Edited by 1200bandit
  • Like 3
Link to comment
Share on other sites

Today wax oil the front chassis legs ( buggier to get of your hair)

Fit the front bumper back on ,wired the spot lights up (no worries about poor headlights)

The clear indicators look good against the white paint 

Had a little go at flattening the bonnet ,comes up well

Project images are available to Club Members Only, Click to become an OMOC Member.

Project images are available to Club Members Only, Click to become an OMOC Member.

Project images are available to Club Members Only, Click to become an OMOC Member.

  • Like 2
Link to comment
Share on other sites

To night started to masking up sticky for n/s door ready to prepare for paint 

All so will blow in the rear 1/4 at the bottom 

The bonnet  turned out really well

Will jack up and remove the lower trim (again) 

 

Project images are available to Club Members Only, Click to become an OMOC Member.

Project images are available to Club Members Only, Click to become an OMOC Member.

Project images are available to Club Members Only, Click to become an OMOC Member.

Project images are available to Club Members Only, Click to become an OMOC Member.

Edited by 1200bandit
  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...